Accelerometer Mounting Studs & Accessories
Junction Boxes & Patch Panels
In addition to instruments, cables and joiners, Kemo can also supply a range of accelerometer mounting studs and sensor accessories commonly used by our customers, these are generally available from stock and we are continuously expanding our range.
Our accessory range includes a wide choice of accelerometer mounting studs, magnets, petrowax and adhesive bases. The options include both isolated and non-isolated types.
Correct accelerometer mounting is a critical part of achieving high quality data with minimal noise and errors, the world of dynamics testing is a tricky one to master, at Kemo we have decades of testing experience and we can advise on teh best solutions for your test.
We can also supply the widely used handheld accelerometer calibrator VTCAL1 which provides an ideal field based testing solution to check correct accelerometer operation prior to test. Operating with a fixed 1grms amplitude and frequency of 159.2Hz, it is battery powered and comes in its own carry case.
KMISO-S1
We hold a stock of isolating mounting studs that can be used with accelerometers, the KMISO-S1 has a 10/32UNF to 10/32UNF thread
DOWNLOAD Datasheet
KMISO-S2
We hold a stock of isolating mounting studs that can be used with accelerometers, the KMISO-S2 has a 10/32UNF to M5 thread
DOWNLOAD Datasheet
KMISO-S3
We hold a stock of isolating mounting studs that can be used with accelerometers, the KMISO-S3 has a 5-40UNC to 10/32UNF thread
DOWNLOAD Datasheet
KMISO-S4
We hold a stock of isolating mounting studs that can be used with accelerometers, the KMISO-S4 has a 5-40UNC to M5 thread
DOWNLOAD Datasheet
KMISO-ADH
Isolated hard anodised aluminium mounting base for adhesive mounting of accelerometers
DOWNLOAD Datasheet
KMMAG-14
Isolated mounting magnet for use with smaller accelerometers. 14.5mm A/F, high pull strength.
DOWNLOAD Datasheet
KMMAG-21
Isolated mounting magnet for use with accelerometers. 21.3mm A/F, ideal for medium size accelerometers, high pull strength.
DOWNLOAD Datasheet
KMMAG-21S
Isolated mounting magnet for use with accelerometers. 21.3mm A/F, ideal for medium size accelerometers, high pull strength. Integrated 10/32UNF stud
DOWNLOAD Datasheet
KMS-ADH1
Adhesive mount for accelerometers, 14.3mm A/F, 10/32UNF integral stud
DOWNLOAD Datasheet
KMS-ADH2
Adhesive mount for accelerometers, 9.5mm A/F, 5/40UNC integral stud
DOWNLOAD Datasheet
KMS-1010S
Mounting stud for accelerometer, 10/32UNF thread full length, Short
DOWNLOAD Datasheet
KMS-1010L
Mounting stud for accelerometer, 10/32UNF thread full length
DOWNLOAD Datasheet
KMS-10M5
Mounting stud for accelerometer, 10/32UNF to M5 thread
DOWNLOAD Datasheet
KMS-10M6
Mounting stud for accelerometer, 10/32UNF to M6 thread
DOWNLOAD Datasheet
KMS-1054
Mounting stud for accelerometer, 10/32UNF to 5/40UNC thread
DOWNLOAD Datasheet
KMS-1028
Mounting stud for accelerometer, 10/32UNF to 1/4-28UNF thread
DOWNLOAD Datasheet
VTCAL1 - Handheld Accelerometer Calibrator
The VTCAL1 is a battery operated handheld calibrator for use with accelerometer and vibration sensors. Operating at a fixed frequency of 159.2Hz and a fixed amplitude of 1grms
DOWNLOAD Datasheet
JB-XX
Kemo’s range of Junction Boxes or Patch Panels are ideal interfaces for test room installation.
Shaker Testing
NVH
Acoustics
DOWNLOAD Datasheet
KMPWAX
Our stock of petrowax is extensive and is available for quick despatch, commonly used to mount accelerometers for simple low frequency tests such as Modal analysis and low level structural testing.
DOWNLOAD Datasheet
KSS-IEPE
The KSS-IEPE allows you to simulate the output from an IEPE accelerometer to test your data acquisition set ups (signal generator also required).
DOWNLOAD Datasheet